Custom wire forms: sourcing from drawing to series

Elementy gięte z drutu stalowego – uchwyty, klipsy i kosz – obok rysunku technicznego

Buyers who move wire form production to a new supplier in Central Europe usually arrive with one of three things: a sample taken from the current supply, a 3D model with no tolerances on it, or a drawing that was written for a machined part. All three can be quoted. What changes is how many questions come back before the quote does, and how closely the first delivery will match what the assembly line actually needs.

Custom bent steel wire parts – brackets, clips and a wire basket – next to a technical drawing

What gets made from wire

The range is wider than the term “wire form” suggests. At one end sit simple parts: clips, fasteners, clamps, hooks, hangers and mounting brackets. At the other end are assemblies in which wire is only the raw material – dishwasher baskets, refrigerator shelves, oven racks, wire shelving and display units, fan and machine guards, chair frames, sterilisation baskets and structural parts of car seats.

The split matters commercially. A simple part is usually made in a single operation on a CNC bending machine, and its price follows the cycle time. An assembly goes through bending, joining and anti-corrosion coating, and its price depends on how many of those steps happen without moving the part between workstations – or between companies.

Drawing, model, sample or sketch

The most efficient input is a STEP model together with a drawing that marks the functional dimensions and their tolerances. The model gives geometry; the drawing says which of those numbers actually matter. A model on its own forces the assumption that every dimension is equally critical, and that inflates the cost of inspection.

A physical sample works too. A 3D scan recovers the geometry, and a drawing can be prepared for your approval before anything is produced. Keep in mind that a sample shows what the part looks like, not what it has to be. If a clip must hold a certain force, or a bracket has to seat in a specific socket, that requirement needs to be written down – a worn sample from the field will not reveal it.

A sketch with a description of the function is a starting point for co-design. The manufacturer proposes the geometry, wire diameter and material, and you approve the drawing before the prototype. This route is slower at the start, but the resulting part is often cheaper because it is agreed around the process from day one.

Tolerances: why “ISO 2768-m” is not enough

Many wire form drawings carry a general tolerance note to ISO 2768-1 in the title block. The standard defines four classes – f, m, c and v – for linear and angular dimensions without individual tolerances. Its scope, however, covers parts produced by metal removal and parts formed from sheet metal. Three-dimensional bent wire is not what it was written for.

In practice this turns into a dispute at first-article inspection. Bend angles in wire scatter naturally, and the position of an end after several bends in different planes accumulates the error of every arc before it. A better approach is to name a handful of functional dimensions – spacing of the mounting points, end positions, overall envelope – and agree tolerances and a check method for those. For parts that fit into a socket or a mating component, a go/no-go shape gauge is the most reliable answer: the part either fits or it does not.

Where that scatter comes from and how the machine compensates for it is covered in our article on CNC wire and tube bending from model to series.

What drives the piece price

Number of bends and number of planes. Each bend is another head movement; a bend in a different plane requires the wire to rotate. A part with five bends in one plane is faster to make than one with three bends in three planes.

Diameter and material. Thin wire bends quickly but needs careful feeding. Thicker wire needs more force and longer cycles. Stainless steel costs more to buy and more to process than structural steel, so it pays to specify it only where the environment genuinely calls for it.

Secondary operations. Flattening an end, piercing a hole, welding two rods together, applying a coating – each adds time and handling. This is where quotes differ most. One supplier does everything in-house; another sends the coating out and adds freight plus the subcontractor’s margin.

Packaging and freight. This is especially relevant for export. Baskets and frames are bulky and light, so the way they are packed – loose, layered with separators, hung on racks – can move the landed cost more than a change of material. Ask for the packaging concept together with the price.

When tooling appears on the quote

A simple part bent on a CNC machine often needs no dedicated tooling at all. The machine program is not a tool that has to be paid for separately.

Tooling costs come in three situations: when the part needs a special bending head or die for a shape that standard tools cannot produce; when rods are joined and a welding fixture has to hold them in position; and when series inspection requires a shape gauge. In high-volume production all three are a normal part of launching the part, and it helps if the supplier builds them in its own toolroom. Corrections after the trial run then take days rather than weeks. Make sure the quote also states who owns the tooling once it has been paid for.

Joining and finishing under one roof

A basket, guard or frame is anything from a few to several dozen rods joined into a grid or a frame. Two techniques are used. Resistance welding – spot or projection – joins rods without filler material and with a small heat-affected zone, which is why it dominates in appliance baskets and wire grids. MIG/MAG or TIG welding suits thicker wire, joints between wire and sheet or tube, and connections that carry high loads.

Joint quality is checked with shear and peel tests plus visual inspection. For load-bearing assemblies, write into the order which test is required and how often. Without that, every supplier applies its own standard, and the offers stop being comparable.

Finishing is typically powder coating, zinc plating or cathodic electrocoating. The choice depends on the operating environment: a fridge shelf, a dishwasher basket and a machine guard outside the building are three different corrosion requirements. Specify them as hours of neutral salt spray testing to EN ISO 9227 rather than by coating name – it leaves the supplier room to offer a cheaper finish that meets the same requirement.

Material – what to ask for

Most wire forms are made from non-alloy steel wire drawn from rod covered by the EN ISO 16120 series. Where the part works elastically, as a clip or a snap fastener does, spring wire to EN 10270-1 or EN 10270-2 is used. Stainless versions – to EN 10270-3 or in acid-resistant grades – are chosen for humid environments, food contact and medical use.

If you are unsure, state the functional requirement instead: does the part need to spring back, what environment does it work in, does it touch food. Selecting the grade is the manufacturer’s job, and a requirement described by function gives room to optimise the price.

From prototype to series

A bent wire prototype typically takes 7–14 days. It is there to check fit, function and appearance – and it is the right moment for changes. Correcting geometry at the prototype stage costs little because it changes the machine program, not a tool.

Once the prototype is approved, series launch at PSI takes 2–3 weeks, and the standard lead time for a production order is 2–6 weeks from drawing approval, depending on complexity. Changes during series production go through a formal change order, and their cost depends on whether they affect material, geometry or tolerances.

How to compare quotes from different countries

Comparing unit prices alone is misleading, and more so across borders. Quotes differ in scope: one includes coating and packaging, another does not; one hides the welding fixture in the piece price, another lists it separately; one assumes sampling inspection, another 100 % gauge checks. Incoterms add one more variable to the landed cost.

Ask each supplier for the price at two or three volume levels, tooling as a separate line with ownership stated, the inspection scope, the Incoterms rule and the type of inspection document – for example a 3.1 certificate to EN 10204. With that breakdown the comparison becomes far easier.

What to send with your enquiry

  • drawing, STEP model, sample or sketch with a description of the function
  • functional dimensions and how they will be checked
  • material or functional requirement (spring action, environment, food contact)
  • corrosion requirement in hours of salt spray testing
  • annual volume, batch size and date of the first delivery
  • packaging, delivery terms and required inspection document

That is enough for the answer to come back as a firm price rather than a list of questions.

Where our wire forms go

We make bent wire components on 2D and 3D CNC bending machines, from wire up to 12 mm in diameter, as part of our CNC wire and tube bending service – together with resistance welding, arc welding and coating. A large share of the output goes to the household appliance industry: dishwasher baskets, refrigerator shelves, oven racks and guides, where repeatability in long series and resistance to moisture and detergents count most.

Have a drawing, a sample or just a sketch of a wire part? Send us your enquiry – we will reply within 48 hours with a proposed process and a price for your volume.

shopping cart